<<< Previous topic - Next topic >>> |
|
Author |
Message |
Horst
Joined: 19 May 2014 Posts: 14
|
Posted: 17.08.2023, 21:28 Post subject: USB-Sticks nicht benutzbar |
|
|
Hallo,
bei Versuchen mit drei USB-Sticks von unterschiedlichen Herstellern werden die Partitionen nicht erkannt.
root@P1607-Koeln:~# uname -a
Linux P1607-Koeln 5.10.15-ssv1 #1 PREEMPT Thu Oct 20 11:00:04 UTC 2022 armv7l unknown
root@P1607-Koeln:~# ls -al /dev/sd*
brw------- 1 root root 8, 0 Aug 17 22:19 /dev/sda
root@P1607-Koeln:~# dmsg
scsi 0:0:0:0: Direct-Access sky 1.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.01 GB/3.73 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda:
sd 0:0:0:0: [sda] Attached SCSI removable disk
root@P1607-Koeln:~# fdisk -l /dev/sda
Disk /dev/sda: 4009 MB, 4009754624 bytes
124 heads, 62 sectors/track, 1018 cylinders
Units = cylinders of 7688 * 512 = 3936256 bytes
Device Boot Start End Blocks Id System
/dev/sda1 ? 251790 470292 839922362 61 Unknown
Partition 1 has different physical/logical beginnings (non-Linux?):
phys=(372, 117, 51) logical=(251789, 73, 11)
Partition 1 has different physical/logical endings:
phys=(314, 114, 52) logical=(470291, 94, 56)
Partition 1 does not end on cylinder boundary
/dev/sda2 ? 1 1 0 65 Unknown
Partition 2 has different physical/logical beginnings (non-Linux?):
phys=(363, 129, 35) logical=(0, 0, 1)
Partition 2 has different physical/logical endings:
phys=(10, 110, 13) logical=(558658, 74, 4)
Partition 2 does not end on cylinder boundary
/dev/sda4 3649 3649 221+ 0 Empty
Partition 4 has different physical/logical beginnings (non-Linux?):
phys=(0, 0, 0) logical=(3648, 57, 51)
Partition 4 has different physical/logical endings:
phys=(0, 0, 0) logical=(3648, 64, 59)
Partition 4 does not end on cylinder boundary
Partition table entries are not in disk order |
|
Back to top |
|
|
hne
Joined: 11 Jul 2008 Posts: 210 Location: Hannover
|
Posted: 28.08.2023, 17:30 Post subject: |
|
|
Offensichtlich wird die Partitionierung des Sticks nicht erkannt, oder der Stick hat keine Partionierung.
Falls der Stick ohne Partitionierung formatiert wurde, kann der Stick direkt gemountet werden, z.B.:
Code: | modprobe vfat
mkdir /mnt/stick
mount /dev/sda /mnt/stick
|
Falls das nicht hilft: Einfach unter Linux eine saubere Partition anlegen und diese Partition dann formatieren. _________________ Henry Nestler |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|